Pattern Feedback and Questions

Post your pattern feedback and questions here!

If you have any problems with your Knit Picks pattern or with a book purchased through Knit Picks, please contact Knit Picks Customer Service at 1.800.574.1323. Thanks!

0 members like this

▶ Reply to This

Replies to This Discussion

Permalink Reply by Knit Picks Admin on October 23, 2008 at 9:07am

That's an Autumn Rose Pullover swatch in the original colorway.
http://www.knitpicks.com/autumn%20rose%20pullover%20pattern%20-%20o...

▶ Reply

Permalink Reply by Elizabeth Smith on October 18, 2008 at 9:36am

Do you have corrected charts for 2 at a time socks. Storey publishing has posted corrected charts. but I can't read the files.
Thanks

▶ Reply

Permalink Reply by Silverfish on October 19, 2008 at 4:53am

I am trying to start on a free pattern (victorian lace headband). I'm confused with the instruction on MAKE KNOT. Instruction goes like this: K1,P1,K1,P1,K1 into 1 st. Pass 2nd - 5th sts over first. Do I make the first 5 stitches in only 1 stitch? Please help. I really like this project.

▶ Reply

Permalink Reply by Susan the Blue Lake Knitter on October 20, 2008 at 4:29pm

I've not knitting this particular pattern, but have done some that have similar requirements. In my opinion, you will need to make sure not to make these stitches too tight or this stitch will be difficult. You knit the first five stitches into ONE stitch, then pass the next five stitches over the stitch you have just knit. When you are doing the K1, P1,K1, P1, K1, DO NOT complete the stitch, wait until you have all five stitches on the needle and then pass through the loop. I surely hope this helps.

▶ Reply

Permalink Reply by AlohaSherry on November 6, 2008 at 9:40am

I am attempting to make Lumpy the Snowman. Do I stuff him with anything? Does the stuffing have to be wool? HELP!

▶ Reply

Permalink Reply by PurlGirl on November 8, 2008 at 9:30am

I used white poly-fiberfill.

▶ Reply

Permalink Reply by AlohaSherry on November 9, 2008 at 10:58am

Mahalo! That is what I bought when I was in town!

▶ Reply

Permalink Reply by jlfknits on November 16, 2008 at 8:46am

Victorian Fingerless Gloves Pattern
by Knit Picks Design Team

Hi ALL! I am desperate to knit this pattern for all my girlfriends who type and freeze their fingers, but...although I knit lace patterns all the time I can NOT get this pattern figured out. I have cast on 14 times now trying to figure it out. If you look at the chart it makes no sense either.

Has anyone successfully knit these mitts?

In the second row it tells you to drop the second YO, but there are no yarn overs to drop. They are still at the other end of the needle.

▶ Reply

Permalink Reply by Lisa R. on October 27, 2009 at 3:00pm

I was having the same problem....No answers to this question yet??? ( But I gave up after casting on only about 4 times---you're more persistent than I am! :))

▶ Reply

Permalink Reply by Customer Service on October 27, 2009 at 3:41pm

Hi Lisa,

I'm sorry, I don't know why this went unanswered but I am will try to help you out. You will be knitting the chart flat, so the YO should line up. You will be picking up the stitches once that part is complete.

Let me know if that isn't the problem!
Stacey
Customer Service

▶ Reply

Permalink Reply by Brenda Boo on March 21, 2011 at 8:00pm

Hi Lisa and jlfknits,

did you figure it out? i was having a hard time as well (even though knitting in the right direction), then i realized i was relying on the numbers at the top of the chart for counting the number of stitches i was doing (bad idea!)

So long story short, when you are knitting the RS at row2, count the chart stitches- it comes out to 9, not 7!

Hope that helps!

-brenda

▶ Reply

Permalink Reply by Moms90 on November 19, 2008 at 9:16am

Dear Members, I have a very basic question. I am attempting to do the Yarn Harlot's Unoriginal Hat posted on her blog page. The pattern calls for 7mm dpns, I am not using a bulky yarn but a chunky yarn double stranded. My question is what is the equivalent of 7mm dpns in US standards. I have found 8mm which translates to US#11 or 6.5mm which translates into 10-1/2 US standards. So is it safe to say I can use either size needle?